I.P.R. Industrial Products
Division of products and speciality chemicals for drilling and piling, a line of specific products for various applications.
FOR DRILLING PROBES OR DRILLS SPECIFICALLY FOR ROCKY SUBSOILS
1 - RECOMMENDED METHODS OF USE/USE
1.1 Highly concentrated surfactant, with good lubricating qualities of the drill bit to increase speed in fractured subsoils and with conglomerate formations; with good foaming power in both fresh and salt water, even with high hardness, to facilitate the escape of even heavy debris from the borehole and with sliding properties to clean the entire battery from dust and sludge and thus avoid the tendency of marly clays to knead.
1.2 Dilute the product with water in a ratio of:
- 0.5-1 kg/m³ in air perforations as anti-dust;
- 0.5-1 kg/m³ as foaming agent in the presence of unfractured dolomitic limestone
- 1.5-4 kg/m³ as foaming agent in the presence of clays;
- 5-15 kg/m³ for aerated sludge and depending on the compactness of the subsoil;
- 0.5-1 kg to clean the hole to be poured into the battery with the addition of water
2 - HANDLING AND STORAGE
2.1 Packaging: 25, 60, 220, 1000 kg PE drums,
2.2 Store in original containers at a temperature between 5 and 40 °C
3 - COMPOSITION/INFORMATION ON INGREDIENTS:
3.1 Surfactant based on Sulfonic acids, C 14-16-Alkane hydroxy and C14-16- alkene, sodium salts 25- 35%.
4 - ECOLOGICAL INFORMATION
4.1 This product is easily biodegradable
4.2 Do not discharge into surface waters
5 - INFORMATION ABOUT REGULATION
5.1 Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Risk phrases: H315 Causes skin irritation. H318 Causes serious eye damage. Precautionary statements: P264 Wash thoroughly with water after handling. P280 Wear protective gloves/protective clothing/eye protection/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313 If eye irritation persists, seek medical advice.
6 - OTHER INFORMATION
6.1 The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements.
FOR DRILLING PROBES OR BOREHOLES. FOR HIGH-PERFORMANCE CLAY SUBSOILS
1 - RECOMMENDED METHODS OF USE/USE
1.1 Highly concentrated surfactant agent, formulated for high performance, with exceptional bulk lubricating qualities to increase speed in unconsolidated or fractured subsoils and conglomerate formations;
1.2 With a very high foaming power and foam-boster effect, both in fresh and salt water, even with high hardness, to facilitate the removal of heavy debris from the hole;
1.3 With sliding properties to clean dust and sludge from the entire battery and thus avoid the tendency of marly clays to knead.
1.4 With a thixotropic effect, it creates a temporary retaining jacket on the hole wall and thus prevents the hole from collapsing and thus occluding.
1.5 Dilute the product with water in a ratio of:
- 0.5 kg/m³ in air perforations as anti-dust;
- 0.5 kg/m³ as foaming agent in the presence of unfractured dolomitic limestone
- 1.5-3 kg/m³ as foaming agent in the presence of clays;
- 5-10 kg/m³ for aerated sludge and depending on the compactness of the subsoil;
- 0.5 kg to clean the hole to be poured into the battery with the addition of water.
2 - HANDLING AND STORAGE
2.1 Packaging: 25, 60, 220, 1000 kg PE drums
2.2 Store in original containers at a temperature between 5 and 40 °C
3 - COMPOSITION/INFORMATION ON INGREDIENTS:
3.1 Surfactant and polymeric substance based on Sulfonic acids ; C 14-16- Alkane hydroxy and C14-16-Alkene, sodium salts 30-40%
4 - ECOLOGICAL INFORMATION
4.1 The components of this product are readily biodegradable
4.2 Do not discharge into surface waters
5 - REGULATORY INFORMATION
5.1 Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Risk phrases: H315 Causes skin irritation. H318 Causes serious eye damage. Precautionary statements: P264 Wash thoroughly with water after handling. P280 Wear protective gloves/protective clothing/eye protection/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313 If eye irritation persists, seek medical advice.
6 - OTHER INFORMATION
6.1 TR 15 BOST-FOAM, due to its high concentration, significantly increases drilling speed and improves hole cleaning; it also gives the possibility of drilling large diameter holes by reducing air consumption and drilling in the presence of fractured formations.
6.2 The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements.
THIXOTROPIC POLYMERIC FOAMING AGENT FOR HIGH-PERFORMANCE DRILLING PROBES OR DRILLS FOR LARGE DIAMETERS AND FRACTURED SUBSOILS
1 - RECOMMENDED METHODS OF USE/USE
1.1Highly concentrated surfactant agent, formulated for high performance, with exceptional bulk lubricating qualities to increase speed in unconsolidated or fractured subsoils and with conglomerate formations
1.2With a very high foaming power with foam-boster effect, both in fresh and salt water, even with high hardness, to facilitate the removal of heavy debris from the hole
1.3With sliding properties to clean dust and sludge from the entire battery and thus avoid the tendency of marly clays to knead
1.4With a thixotropic effect, it creates a temporary retaining jacket on the hole wall and thus prevents the hole from collapsing and therefore occluding
1.5Dilute the product with water in a ratio of:
- 0.5 kg/m³ in air perforations as anti-dust;
- 0.5 kg/m³ as foaming agent in the presence of unfractured dolomitic limestone
- 1.5-3 kg/m³ as foaming agent in the presence of clays;
- 5*10 kg/m³ for aerated sludge and depending on the compactness of the subsoil;
- 0.5 kg to clean the bore to be poured into the battery with the addition of water
2 - HANDLING AND STORAGE
2.1Packaging: PE drums of 25, 60 ,220 , 1000 kg.
2.2Store in original containers at a temperature between 5 and 40 °C
3 - COMPOSITION/INFORMATION ON INGREDIENTS:
3.1Surfactant and polymeric substance based on Sulfonic acids ; C 14-16- Alkane hydroxy and C14-16-Alkene, sodium salts 30-40%
4 - ECOLOGICAL INFORMATION
4.1The components of this product are readily biodegradable
4.2Do not discharge into surface waters
5 - REGULATORY INFORMATION
5.1Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Risk phrases: H315 Causes skin irritation. H318 Causes serious eye damage. Precautionary statements: P264 Wash thoroughly with water after handling. P280 Wear protective gloves/protective clothing/eye protection/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313 If eye irritation persists, seek medical advice.
6 - OTHER INFORMATION
6.1From experience gained on work sites, we bring the following to your attention: The foam that escapes from the drill hole during the drilling phase must absolutely be contained and conveyed into an airtight container, in order not to disperse it into the environment. If this is not possible, because the foam would immediately fill the container, you should treat it with special foam blowers and send the recovered water to an authorised landfill site.
6.2Outline of the advantages of using the TX 20 POLI-FOAM in relation to other circulating and air drilling systems:
| AIR | MISTI | AERATI | TX20 POLI-FOAM | |
|---|---|---|---|---|
| Proportional increase in penetration | NO | NO | NO | SI |
| Deviation control | NO | NO | SI | |
| Auction differential reduction | NO | NO | NO | SI |
| Circulation loss control | NO | NO | NO | SI |
| Tolerance of influence flow formation | NO | NO | SI | |
| Low annular velocity | NO | NO | SI | |
| Low air volume required | NO | SI |
6.3Geological areas for which TX 20 POLI-FOAM is appropriate:
| AIR | MISTI | AERATI | TX20 POLI-FOAM | |
|---|---|---|---|---|
| Low-pressure aquifers | NO | NO | NO | SI |
| Hard formations in the presence of water | NO | NO | SI | |
| Hard dry formations | NO | NO | SI | |
| Non-consolidated formations | SI | |||
| Fractured formations | NO | NO | NO | SI |
| Formations with deviations | NO | NO | SI | |
| Large-diameter holes | SI | |||
| Holes with a depth of more than 1000 m. | SI |
–
6.4TX 20 POLI-FOAM, due to its high concentration and with the help of added polymers, significantly increases drilling speed and improves hole cleaning; it also gives the possibility of drilling large-diameter holes by reducing air consumption and drilling in the presence of fractured formations, thus being superior to corresponding drilling systems with mud or reverse cycle fluids
6.5The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements. It should therefore not be interpreted as a guarantee of any specific product properties. Our technical service is always available for further information.
CONCENTRATED THIXOTROPIC POLYMERIC FOAMING AGENT FOR HIGH-PERFORMANCE DRILLING PROBES OR DRILLS FOR LARGE DIAMETERS AND FRACTURED SUBSOILS
1 - RECOMMENDED METHODS OF USE/USE
1.1 Highly concentrated surfactant agent, formulated for high performance, with exceptional bulk lubricating qualities to increase speed in unconsolidated or fractured subsoils and with conglomerate formations
1.2 With a very high foaming power with foam-boster effect, both in fresh and salt water, even with high hardness, to facilitate the removal of heavy debris from the hole
1.3 With sliding properties to clean dust and sludge from the entire battery and thus avoid the tendency of marly clays to knead
1.4 With a thixotropic effect, it creates a temporary retaining jacket on the hole wall and thus prevents the hole from collapsing and therefore occluding
1.5 Dilute the product with water in a ratio of:
- 0.3 kg/m³ in air perforations as anti-dust;
- 0.3 kg/m³ as foaming agent in the presence of unfractured dolomitic limestone
- 1.0-2 kg/m³ as a foaming agent in the presence of clays;
- 3-8 kg/m³ for aerated sludge and depending on the compactness of the subsoil;
- 0.3 kg to clean the bore to be poured into the battery with the addition of water
2 - HANDLING AND STORAGE
2.1 Packaging: 25, 60, 220, 1000 kg PE drums
2.2 Store in original containers at a temperature between 5 and 40 °C
3 - COMPOSITION / INFORMATION ON INGREDIENTS
3.1 Surfactant and polymeric substance based on Sulfonic Acids, C 14-16-Alkane hydroxy and C14-16-alkene, sodium salts 30-50 %.
4 - ECOLOGICAL INFORMATION
4.1 The components of this product are readily biodegradable
4.2 Do not discharge into surface waters
5 - REGULATORY INFORMATION
5.1 Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Risk phrases: H315 Causes skin irritation. H318 Causes serious eye damage. Precautionary statements: P264 Wash thoroughly with water after handling. P280 Wear protective gloves/protective clothing/eye protection/face protection. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337+P313 If eye irritation persists, seek medical advice.
6 - OTHER INFORMATION
6.1 From experience gained on work sites, we bring the following to your attention: The foam that escapes from the drill hole during the drilling phase must absolutely be contained and conveyed into an airtight container, in order not to disperse it into the environment. If this is not possible, because the foam will immediately fill the container, you should treat it with special foam blowers and send the recovered water to an authorised landfill site. If the product should be carelessly dispersed in the environment, if in the presence of plantations such as olive groves, vineyards, peach orchards, etc., and especially on land that has been treated with herbicides, it could happen that the plant's leaves turn yellow for a season, but the plant does not dry out (there has never been a case), and continues its vegetation, also bearing fruit. The following year, the normal vegetation cycle returns. Before starting work, it is strongly recommended to ascertain whether any herbicides have been used on the site in order to take the necessary precautions. On no account, therefore, disperse the product into the environment and try to contain the water and foam escaping as best as possible.
6.2 Outline of the advantages of using TW 30 WINPOL-FOAM in relation to other circulating and air drilling systems:
| AIR | MISTI | AERATI | TW 30 | |
|---|---|---|---|---|
| Proportional increase in penetration | NO | NO | NO | SI |
| Deviation control | NO | NO | SI | |
| Auction differential reduction | NO | NO | NO | SI |
| Circulation loss control | NO | NO | NO | SI |
| Tolerance of influence flow formation | NO | NO | SI | |
| Low annular velocity | NO | SI | ||
| Low air volume required | NO | SI |
–
6.3 Geological areas for which TW 30 WINPOL-FOAM is appropriate:
| AIR | MISTI | AERATI | TW 30 | |
|---|---|---|---|---|
| Low-pressure aquifers | NO | NO | NO | SI |
| Hard formations in the presence of water | NO | NO | NO | SI |
| Hard dry formations | NO | NO | SI | |
| Non-consolidated formations | NO | SI | ||
| Fractured formations | NO | NO | NO | SI |
| Formations with deviations | NO | NO | SI | |
| Large-diameter holes | SI | |||
| Holes with a depth of more than 1000 m. | SI |
–
6.4 TW 30 WINPOL-FOAM, due to its high concentration and with the help of added polymers, significantly increases drilling speed and improves hole cleaning; it also gives the possibility of drilling large-diameter holes by reducing air consumption and drilling in the presence of fractured formations, thus being superior to corresponding drilling systems with mud or reverse cycle fluids
6.5 The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements. It should therefore not be interpreted as a guarantee of any specific product properties. Our technical service is always available for further information.
LIQUID EMULSION POLYMER FOR PREPARING DRILLING AND BOREHOLE FLUIDS
1.1 Polymer to be used in the preparation of drilling and borehole fluid; the product is easily soluble in water and does not leave residues or lumps Being highly concentrated, low dosages are used In combination with the foaming agents TH10 STONE FOAM ,TR15 BOST FOAM, TX 20 POL POL FOAM or TW 30 WIN POL FOAM it considerably helps the rotation of the battery and dampens mechanical vibrations TP-L1202 POLYMER is used for Micropiles and Piling as a diaphragm; Microtunnels for horizontal drilling and in Boreholes allows viscous drilling fluid to stabilise fractured subsoils, controls fluid loss and also acts as an inhibitor and protector in the presence of clays
1.2 Dilute the product with fresh water in a ratio of:
- 1.0-1.5 kg/m³ in the presence of clay;
- 1.5-2.0 kg/m³ in the presence of Shale;
- 2.0-2.5 kg/m³ in the presence of silt and fine sand;
- 2.5-3.5 kg/m³ in the presence of gravel and coarse sand;
- 3.0-5.0 kg/m³ in the presence of coarse gravel and excavations;
2 - HANDLING AND STORAGE
2.1 Packaging: 25 kg PE drums.
2.2 Store in original containers at a temperature between 5 and 40 °C
3 - COMPOSITION/INFORMATION ON INGREDIENTS:
3.1 Sodium acrylamide-acrylate emulsion copolymer with viscous opalescent appearance.
4 - ECOLOGICAL INFORMATION
4.1 POLYMER TP-L 1202 is easily dispersible with tap water or a 5% sodium hypochlorite solution
5 - REGULATORY INFORMATION
5.1 Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Non-hazardous
6 - OTHER INFORMATION
6.1 The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements. Our company's Technical Service will be happy to offer further advice and assistance, however, customers must ensure (if necessary by appropriate testing) that the product is suitable for their purposes and/or conditions of use, and that their facilities, equipment and arrangements are suitable for handling and/or use of the product. Accordingly, our company disclaims any liability for loss or damage resulting from the use of the product, this information, advice or service, except as expressly agreed in its terms and conditions of sale.
NATURAL ORGANIC POWDER POLYMER FOR PREPARING HIGH-PERFORMANCE DRILLING AND PROBING FLUIDS WITH THIXOTROPIC EFFECT TO INCREASE DEBRIS CARRYING CAPACITY AND INCREASE SPEED
1.1 Polymer to be used in the preparation of drilling and borehole fluid; the product is easily soluble in water and leaves no residue or lumps In combination with the foaming agents TH 10,TR 15 or TX 20, it greatly aids battery rotation and dampens mechanical vibrations TP-P 2202 POLYMER has a pronounced thixotropic effect, resulting in a viscous, sticky drilling fluid for stabilising the walls of fractured subsoils or when encountering sand
1.2 Dilute the product with fresh water at a ratio of: - 2 - 5 kg/m³ depending on the diameter, depth, type of underlying formation; however, if clay is encountered, it is advisable to add TP-P 2202 POLYMER at the same percentages
2 - HANDLING AND STORAGE
2.1 Packaging: 25 kg paper sacks.
2.2 Store in the original packaging, at a temperature between 5 and 40 °C, away from sources of moisture.
3 - COMPOSITION/INFORMATION ON INGREDIENTS:
3.1 Powdered polymer of natural organic origin
4 - ECOLOGICAL INFORMATION
4.1 POLYMER P RD 2202 is non-toxic and can be used in environmentally friendly areas
4.2 Do not discharge into surface waters
5 - REGULATORY INFORMATION
5.1 Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Non-hazardous
6 - OTHER INFORMATION
6.1 The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements.
NATURAL ORGANIC POWDER POLYMER FOR PREPARING HIGH-PERFORMANCE DRILLING AND PROBING FLUIDS WITH THIXOTROPIC EFFECT TO INCREASE DEBRIS CARRYING CAPACITY AND INCREASE SPEED
1.1 Polymer to be used in the preparation of drilling and borehole fluid; the product is easily soluble in water and leaves no residue or lumps In combination with the foaming agents TH 10,TR 15 or TX 20, it greatly aids battery rotation and dampens mechanical vibrations TP-P 2202 POLYMER has a pronounced thixotropic effect, resulting in a viscous, sticky drilling fluid for stabilising the walls of fractured subsoils or when encountering sand
1.2 Dilute the product with fresh water at a ratio of: - 2 - 5 kg/m³ depending on the diameter, depth, type of underlying formation; however, if clay is encountered, it is advisable to add TP-P 2202 POLYMER at the same percentages
2 - HANDLING AND STORAGE
2.1 Packaging: 25 kg paper sacks.
2.2 Store in the original packaging, at a temperature between 5 and 40 °C, away from sources of moisture.
3 - COMPOSITION/INFORMATION ON INGREDIENTS:
3.1 Powdered polymer of natural organic origin
4 - ECOLOGICAL INFORMATION
4.1 POLYMER P RD 2202 is non-toxic and can be used in environmentally friendly areas
4.2 Do not discharge into surface waters
5 - REGULATORY INFORMATION
5.1 Hazard labelling according to Regulation (EC) 1272/2008 (CLP) and subsequent amendments and adjustments: Non-hazardous
6 - OTHER INFORMATION
6.1 The details contained in this sheet refer to the current state of knowledge and experience and are characteristics of our product with respect to any possible technical requirements.